Acura MDX Serpentine Accessory Belt Replacement Guide
How to change the serpentine accessory belt on the 3.5L V6 VTEC engine in a 1st generation 2001 to 2006 Acura MDX.
ByPaul B. Michaels
Author & Photographer
Auto Mechanic Since 1989
Owners of other Acura or Honda vehicles such as the RDX, ILX, TLX, RLX, TL, CL, RSX, RL, TSX, ZDX, NSX, Integra, Pilot, Accord, Civic, Fit, Clarity, CR-V, CR-Z, HR-V, Odyssey, Element and Ridgeline with the VTEC 3.5L V6 engine may also find these DIY instructions to be helpful.
A few compatible replacement serpentine accessory belts with their part numbers are as follows: Bando 6PK2135, Gates K060841, Dayco 5060840,ACDelco 6K841 and Mitsuboshi 6PK2135.
The tools required to complete this procedure include a 14mm socket with a long handled 1/2" drive ratchet and an optional breaker bar.
You may opt to purchase a specialized 14mm serpentine belt tool such as the Schley SL10950, Lisle 59000,Honda YA9317 andAssenmacher HON1419.
If you have recently driven the SUV, I recommend allowing the engine to cool off for at least an hour or two before you replace the belt.
Then locate the blue plastic wire loom holder that secures the black wire loom to the engine bay near the pulleys.
Carefully lift the wire loom holder off its mounting bracket and move it away from the pulleys and belt.
Then use a flathead screwdriver to pry back the release tab on the mounting bracket for the power steering fluid reservoir (grey plastic with a red cap).
Lift the power steering fluid reservoir up and off its mounting bracket. Move it off to the left away from the pulleys and belt.
Above is the belt routing diagram from the 2006, 2007 & 2008 Honda Pilot service manual, which also shows you which direction to rotate the tensioner arm assembly to release the tension on the old belt. I labeled the pulleys and indicated in which direction the windshield and front bumper are located.
Make sure that the socket is securely in place.
This is the counterclockwise direction if you are standing on the left (passenger) side of the engine bay.
Carefully hold the ratchet in place rotated back towards the windshield with the tension released and slip the old belt off the top of the power steering pump pulley at the top of the engine.
Avoid placing your fingers in between any of the pulleys and the belt.
Slowly return the ratchet to the starting position towards the front of the SUV.
Inspect the old belt for fraying, chunks of missing rubber and exposed metal strands.
If the old belt is in good condition, consider keeping it as an emergency backup just in case the new belt fails prematurely.
Check the idler and tensioner pulleys to make sure they spins freely. If they do not, replace them with new pulleys.
The new idler and tensioner pulleys with their part numbers are as follows: Hayden Automotive 5979, ACDelco 38006, Gates 38006 andDayco 89007.
If it seemed very easy to rotate the tensioner assembly and release the old belt, the OEM tensioner assembly might be worn out and should be replaced. Another symptom of a weak tensioner arm is an intermittent "chirping" sound coming from the belt.
A compatible replacement tensioner assembly is part number Continental Elite 49349.
I recommend buying the Bando 6PK2135 serpentine belt since it has excellent reviews on Amazon.
A good tip to remember when you are installing the new belt is that the ribbed side of the belt will be wrapped around ribbed pulleys and the smooth side will go against the smooth pulleys.
Start by wrapping the ribbed side of the new belt around the large crankshaft pulley at the rear lower part of the engine.
Place the 14mm socket and long handled 1/2" drive ratchet over the bolt head on the tensioner assembly pulley.
Pull the ratchet handle back towards the windshield and the rear of the SUV (counterclockwise).
Carefully slip the last loop of the new serpentine belt over the power steering pulley.
Slowly rotate the ratchet handle back to the starting position closer to the front of the SUV.
Double check that the new belt is properly routed around the crankshaft, A/C, idler, tensioner, alternator and power steering pump pulleys.
Push the power steering fluid reservoir back down on to its mounting bracket.
Push the blue plastic wire loom holder on to its mounting bracket.
Start the engine and listen closely for any strange sounds that may indicate an improperly routed belt or a worn out pulley. If you hear any strange noises, immediately turn off the engine and check that you have properly routed the new belt.
Be sure to record the belt change in your vehicle's service records.
For more, please check out all of my .